60 Full Auto Cold Roll Laminator Heat Assisted Laminationg Machine Wide Format

60 Full Auto Cold Roll Laminator Heat Assisted Laminationg Machine Wide Format
60 Full Auto Cold Roll Laminator Heat Assisted Laminationg Machine Wide Format
60 Full Auto Cold Roll Laminator Heat Assisted Laminationg Machine Wide Format
60 Full Auto Cold Roll Laminator Heat Assisted Laminationg Machine Wide Format
60 Full Auto Cold Roll Laminator Heat Assisted Laminationg Machine Wide Format
60 Full Auto Cold Roll Laminator Heat Assisted Laminationg Machine Wide Format
60 Full Auto Cold Roll Laminator Heat Assisted Laminationg Machine Wide Format
60 Full Auto Cold Roll Laminator Heat Assisted Laminationg Machine Wide Format
60 Full Auto Cold Roll Laminator Heat Assisted Laminationg Machine Wide Format
60 Full Auto Cold Roll Laminator Heat Assisted Laminationg Machine Wide Format

60 Full Auto Cold Roll Laminator Heat Assisted Laminationg Machine Wide Format

60 Full - auto Low Temp Wide Format. This 60 Full - auto Low Temp. With Stand can be widely used for pre - masking vinyl graphic, mount prints on substrate, over laminating inkjet prints and so on.

The cold laminator is used to after printing. Shop and copy shop to do lamination work, adding a protective layer on books cover, photographic, color pages, documents, charts, drawings, indoor advertising products, etc. This laminator 1600C6+ is low heated cold laminator with liner and without. Liner, a wide range of application. It can be used both cold laminating and hot laminating with low temperature, to strip coil backing paper, to roll picture.

Especially when work in hot laminating conditions, it will improve the. Coating effect by heating the roller.

Its multiple-function, easy operation and high efficiency. Adopts low temperature cold laminating, mainly used to solve the issue that cold laminated images are hazy.

Stainless steel feeding table 130mm (5) upper rubber roller Auto take up system Anti tilt and anti fold device (Origin) Pressure and height adjust hand wheel Infrared temperature control device. This laminator comes with 2 pcs heating glass tube in the package. When hot laminating, the temperature is 5060 degree, the highest. From 0 to 10m (393) per minute. 0.3 - 0.5KW / h.

Preset temperature: Find out hot/cold framed switch, choose the "hot ", temperature display screen will light up, the left number is preset temperature, the right number is roller temperature, press SETkey and then through UP and. DOWN adjust preset temperature, after adjust it and press SETkey confirm it.

When cold film, the preset temperature is 50. The max temperature is 50.

According to the viscosity of the glue, and adjust preset temperature. Turn: This machine dont have continuous reverse function. In the "continuous" state it only can " turning". In the "point move" state, through the pedal switch can "turning" or "reverse". Governor knob: clockwise to grow speed, counter-clockwise to slow down; Please select the appropriate speed to ensure the laminating effect, when stop coated please select "point move". General Using and installation method. NoteThe hex nuts must be tighten! If loose will appear heating power electric spark change, and broken wire and other components. There is a Filter Voltage Stabilizer at the right back of the machine, as the picture;Pull the knob of the filter voltage stabilizer up softly, air pressure increases when rotating at clockwise direction. Air pressure decreases when rotating at the counterclockwise direction. Normal air pressure is 0.2Mpa. The adjust of rubber covered roller s parallelism. Whether the parallelism adjusts well or badly, also can in fluent.

Effect quality and off tracking, the parallelism has been adjusted well when leaving the factory, but it still needs adjusting after using a long. A-Pressure adjusting valve B-Pressure adjusting valve C-locking screw nut.

When the parallelism gap of the rollers is slight, it can be adjusted by the following method. Moving screw A to adjust the balance of the roller while it s rising.

Find out which side of the roller rises slower, then move the screw outward (Or find out which side rises faster, then move the screw inward). Then raise and lower the roller until the roller is balanced. Move screw B to adjust the balance of roller while it s falling. Find out which side of the roller falls slower, then move the screw outward (Or find out which side falls faster, then move the screw inward). Adjust the air pressure to 0.1MPa, the movement of the roller is slower than normal. Laminating work is an extremely fine, technical stronger work, for beginners should have experience in the technicians under guidance of Membranae tectoria work, the below only show the general operation. Fall down tne upper nip roller. Press the "continuous" and "turning" switch, governor rotate to the "1". Open the "hot" switch and et the heat temperature which we required, then nip roller began to heating. Hot laminating, the preset temperature is 90 , when low temperature/cold laminating, the preset temperature set to 45 (to working temperature need about 10-20 minutes). Take out a roll of film and install into material roller, then let roll into material feeding roller scaffold and pulling the film with the hand, shall ensure the appropriate resistance, through the next to the damping handwheel adjust it. Let framed chart scroll in carton, then packed in rewinding stent and fixed them.

The general questions and methods Problem. Control panel have no electricity.

Check the power and emergency button. Lift a little the upper roller. Adjust friction Tighten sprocket key.

Contact with motor or governor. Laminated paper isn't clear and have white point.

Contact suppliers to replace film. Laminated paper have pleated bubbles. Put paper in 90 angle into rubber roller.

Increase speed and reduce temperature. Adjust to the required temperature. 74" x 27" x 45 (1880mm x 680mm x 1140mm).

81" x 28" x 28 (2060mm x 710mm x 720mm). Left support of feeding roll. Right support of feeding roll.

Table 2: Steel stand packing list. Hex screw M8 x 80. If by e-packet, 7-15 days to USA, and 2-4 weeks to other most countries. S&H will be determined based upon your address.

We believe that we can produce a positive outcome to any situation to earn your like. The item "60 Full Auto Cold Roll Laminator Heat Assisted Laminationg Machine Wide Format" is in sale since Thursday, August 17, 2017.

This item is in the category "Business & Industrial\Office\Office Equipment\Laminating Equipment\Laminating Machines". The seller is "optim-parts" and is located in Los √Āngeles. This item can't be shipped, the buyer must pick up the item.


60 Full Auto Cold Roll Laminator Heat Assisted Laminationg Machine Wide Format